Steel & Slider Cover (Telescopic Cover)

0
264

STEEL COVER

The use of the telescope cover has become very important in coping with the rapod increase in technology and automation of the machine tool industry in recent years.

This rapod development requires such things as rational busimess practices, expanded productivity, and good factory, management.

Shinsung has for a long time been cooperating with various machine tool makers to improve our products. The telescope cover is a result of this. This telescope cover has, with the use of advanced technology, been produced to conform to many types of machines. Below is a detailed explanation of the telescope cover.

1. SPECIAL FEATURES :

We will produce to fit any machine.

2. APPROVED SPEED : We produce on the premise of 10m to

12m. If you need to go over this, we will consult with you

directly.

3. MATERIALS :

We produce in both iron and stainless steel

4. FINISHED SURFACE : BUFF, Black finish and Zinc plating.

■ Below are the different shapes of the telescope cover.

※ We can produve shapes outside of these, so please consult with us.

■ Struction

1. COVER BOX
We use a special kind of steel plate for the cover box. There are 4 standards ofr the thickness of the plate:1.2mm,1.6mm, 2.3mm, 3.2mm.

The thickness is decided based on the cover measurements and the necessary intensity.

2. WIPER
This special wiper is used on the cover but it can also be used on the side according to the design. (made of polyurethane) The heat resistance of the wiper is the standard 40 degrees to 100 degrees celsius.

It is also durable enough to protect against water and oil. We can also make the telescope cover without wipers.

3. WIPER COVER
We can install a steel cover on the wiper in case you need to protect the wiper form high temperature industrial dust.

4. ROLL UP STRUCTURE
Inprinciple, both ends of the cover roll up. This is the so called box of each of the covers can match perfectly. This can also put tension on the wiper accurately. Of course, we can design a cover which goes up step by step. In order to avoid the cover itself lifting up, each wiper should be suppressed by adequate tension.

5. NON SKID PLATE
There are many advantages in putting a non stick plate th the cover box.

For example, there is a column inside which is in the folthold. We have introduced this as a place for tools.

6&7. THE SUPPORT ROLLERS GUIDE SHOE
In the small size and medium size cover, we use a synthetic resin guide shoe. In the big size covers, in order to reduce the friction resistance, the roller itself uses a ball bearing roller.?? When the guide system uses a roller and when the metal of movable parts isn’t strong, to provide a special support rail parallel to the movable part.

8. SUSPENDED METAL FITTINGS
With the heavy cover, there is a removable suspended fitting, it is easy to use.

9. INSPECTION HOLE
An inspection hole has been put on the top of the box in order to inspect the parts which are necessary for, the maintance, such as the spindle and the movable part etc. Please be careful because will be longer than you expented If you hole or make it transparent.

10. BRACKET
For the movable part to move, when there is no margin to move because of the design of the machine tool, we use the bracket in the diagram. The point is a bracker joint that does not restrict the movement of the cover.

11. SUPPORT RAIL
When the movable part is not strong anough, you need a support rail accompany the roller guide.

■ COST AND DESIGN OF THE TELESCOPE COVER
(please consult with us from beginning)

We think an important point for the machine tool maker is how small the telescope cover becomes when it contracts. Looking from the point of view of the cost of the cover, it is better for the box unit to be bigger and there be less units than for the cover to bemade up of a lot of small box units. This will lower the cost. So please consult with us from the early stage of your plan in order to have the most cost effective design.

When you need to design the minimum size cover, you have to make it very small. So it is difficult for each part to have balance. Terefore our company adopts a rail guide system.

■ How to attach and repair

In case of attaching COVER, be sure to attach in a state contracted(Min) by optional deciding. STEEL SLIDE COVER should be cleaned once a week at least and oil is supplied.

■ Matter to be clarified at order time.

■ THE SHAPES OF THE COVER WHEN CONTRACTING